On a laboratory bench at the University of Pennsylvania, hundreds of films thinner than paper are being placed one upon another by hand, a patient answer to an old dilemma: the materials that insulate best tend to break, and the materials that endure tend to let heat escape. Drawing on the same humble plastic used in emergency blankets and spacecraft, the team has shown that a stacked, layered form can bend, bear heavy pressure, and still hold warmth, which matters for the shelters humanity may someday raise on the Moon. The work is still small, measured in centimeters rather than meters, but
Penn Engineers Turn Emergency-Blanket Mylar Into Tough Insulation for Future Moon Habitats
Even breathing near the stack can send the layers flying.
Why does a thermal blanket material matter for the Moon?
Because insulation there has to be tough as well as efficient. Penn's stacks of hundreds of Mylar layers bend, take heavy compression, and still insulate.
What was the compression test?
About 20 megapascals, roughly 200 pounds on a fingertip-sized area, repeated 10 times. The stacks survived all of it.
Worth noting that 10 cycles is not years of use. The alumina-coated stacks also hit the limit of the lab equipment, so we don't know where they actually fail.
What about the particle finding?
The tiny antiblocking particles in commercial film seem to carry much of the heat from sheet to sheet in a vacuum. That could let engineers design them deliberately.
And thinner films didn't beat medium ones. The particle explanation is the researchers' suspicion, not a settled result.
How close is this to real use?
Not close. Samples are about one square centimeter, stacked by hand with tweezers.
Right. Whether meter-scale sheets keep the same performance is unknown, and so is how they handle scratches, impacts, and repeated bending.
So the next step is manufacturing?
Yes, likely coating large rolls of Mylar, then testing whether the lab results hold.
Le Pouls
- A habitat wall on the Moon must withstand the push of indoor air while enduring years of bumps, and most good insulators crack under that demand.
- Aerogels insulate well but shatter easily, while reflective multilayer sheets tear on contact, leaving engineers forced to choose between strength and warmth.
- Researchers stacked hundreds of Mylar films, coated some with aluminum oxide, and squeezed them to about 20 megapascals ten times in a row without losing their insulating performance.
- Surprising heat paths through microscopic particles on the film surfaces mean that thinner sheets do not automatically insulate better, reshaping the design plan.
- The material remains a one-square-centimeter sample built by hand, and the next step is continuous coating of meter-sized rolls to see whether the lab results hold at scale.
On a laboratory bench at the University of Pennsylvania, hundreds of films thinner than paper are being placed one upon another by hand, a patient answer to an old dilemma: the materials that insulate best tend to break, and the materials that endure tend to let heat escape. Drawing on the same humble plastic used in emergency blankets and spacecraft, the team has shown that a stacked, layered form can bend, bear heavy pressure, and still hold warmth, which matters for the shelters humanity may someday raise on the Moon. The work is still small, measured in centimeters rather than meters, but it also reveals that the tiny bumps on a sheet's surface quietly govern how heat moves, a reminder that even the simplest things hold surprises.
In a lab at the University of Pennsylvania, a researcher uses tweezers and tiny weights to stack plastic films far thinner than paper. Even a breath near the pile can send the layers flying. The painstaking work has produced a new insulation, made from the same Mylar used in marathon emergency blankets, and designed with the Moon in mind.
The material, called HyLIFS, comes from a team at Penn Engineering led by Igor Bargatin, with first author Danielle R. Levin and co-authors Matthew F. Campbell, Gulzhan Aldan, and Orevaoghene H. Omodior. Their goal was to escape a familiar tradeoff. Lunar materials must survive launch and years of life inside a base, yet aerogels crack under impact, and reflective multilayer sheets tear under contact. Making insulation tougher often lets more heat through.
The team stacked hundreds of thin Mylar films, varied their thickness, and coated some with a whisper-thin layer of aluminum oxide to stiffen them. In a vacuum, the best stacks insulated comparably to advanced materials while staying flexible. The real surprise came under compression. Pressed to about 20 megapascals, roughly 200 pounds on a fingertip-sized area, the stacks survived ten cycles in a row. Levin admits they had feared failure.
The experiments also revealed that tiny antiblocking particles on commercial films create contact points where much of the heat travels. This explains why the thinnest films did not insulate better than medium ones. Engineers may someday control those particles deliberately.
The material is still far from a building site. Samples measure about one square centimeter and are cut and stacked by hand. The next hope is coating large rolls of Mylar continuously, producing meter-scale sheets. Whether they will match lab performance, and how they will handle bending, impacts, and scratches, remain open questions. In Levin's words, the simplest configuration turned out to be the best one.
In a lab at the University of Pennsylvania, a researcher uses two pairs of tweezers and a handful of tiny weights to stack plastic films, each far thinner than a sheet of paper. Even breathing near the pile can send the layers flying. That painstaking work has produced a new kind of insulation, built from the same material as the emergency blankets handed out at marathon finish lines, and designed with the Moon in mind.
The material is called hybrid layered insulating film stacks, or HyLIFS. It was described in ACS Applied Materials & Interfaces by a team at Penn Engineering. The senior author is Igor Bargatin, an associate professor in Mechanical Engineering and Applied Mechanics. The first author is Danielle R. Levin, a recent Penn doctoral graduate in chemistry who also earned a master's in the same department. The co-authors are Matthew F. Campbell, Gulzhan Aldan, and Orevaoghene H. Omodior.
The problem they set out to address is a tradeoff. Anything used on a lunar base has to survive packing, launch, transport, installation, and then years of bumps from people living and working inside. Many of the best insulators are fragile. Aerogels, which are mostly empty space and have been used in industrial pipelines and on NASA's Mars rovers, are light and hold heat well, but their delicate structure makes them vulnerable to impact and compression. Multilayer insulation, built from reflective sheets separated by spacers, is very good at limiting radiated heat but is not meant to bear weight, and routine contact can tear it. Making insulation tougher often lets more heat through. Bargatin says the ideal material resists both damage and heat loss.
The team turned to Mylar, formally biaxially oriented polyethylene terephthalate, or BoPET. It is already common in aerospace, and with an aluminum coating it reflects infrared radiation. Instead of relying on one sheet, the researchers stacked hundreds of thin ones, varied the film thicknesses, and coated some samples with an extremely thin layer of aluminum oxide, or alumina, to stiffen them. In a vacuum, the best stacks reached thermal conductivity comparable to other advanced vacuum insulation materials while staying flexible.
The compression tests were the surprise. Inside a lunar habitat, interior air pressure would push against walls facing the vacuum outside, so the team tested for that kind of load. Alumina-coated stacks tolerated the highest compressive stress the lab equipment could deliver without losing insulating performance. The researchers then compressed samples to about 20 megapascals, roughly 200 pounds of force on an area the size of a fingertip, and repeated it 10 times. Levin says they feared failure, but the stacks survived all 10 cycles in a row.
The experiments also exposed something about how heat moves. Commercial plastic films contain tiny antiblocking particles that poke slightly above the surface and keep thin sheets from clinging together. Using mathematical models of heat transfer between layers and comparing them with measurements, the team found that in a vacuum much of the heat passing from one sheet to the next travels through the contact points those particles create. That may explain why thinner films did not help as expected: the thinnest alumina-coated films they could characterize performed about like medium-thickness ones. The researchers suspect thinner sheets make more contact through the particles, offsetting the benefit of extra layers. Levin notes the contacts change as pressure rises and films deform. Engineers might eventually control the size, number, and placement of the particles on purpose.
The material is still far from a building site. Current samples measure about one square centimeter and take hours of cutting and manual stacking. The team hopes to coat large rolls of Mylar continuously, producing sheets measured in meters, which could also let them tune thickness, coatings, and particle distribution beforehand. Open questions remain: whether large versions will match laboratory performance, and how the stacks handle repeated bending, impacts, and scratches. Levin summed up the work by saying the simplest configuration turned out to be the best one.
Citations marquantes
The stacks didn't survive just one high stress cycle -- they survived 10 in a row.— Danielle R. Levin, first author
The ideal material is both resistant to damage and to the loss of heat.— Igor Bargatin, senior author, University of Pennsylvania